MKC Tools

Expert Mark V Repair Service and Parts






Part #
Description
Price
MKC
MKC-026

Mark V Tool Rest Handle Upgrade

In stock ready to ship.
Mark V Tool Rest Handle Upgrade

$19.95
MKC

Power Tool Woodworking for Everyone by R. J. DeCristoforo. 1955 edition featuring the Greenie 50s model Mark V machine. This copy in very nice condition including the mylar cover. Clean, tight binding and no marks. This book is probably the best accessory you can have for a Shopsmith. It has a chapter on each function of the machine as well as how to make many useful jigs and other helps.

$19.50
MKC

Bondus Cushion grip T handle Hex wrench ball end 5/32" long reach. This wrench is just what you need to tighten those hard to get to way tube set screws in the pivot base. If those screws aren't tight the way tubes can slip out during lathe operations creating a very dangerous situation. Because of the hinge bar inside the pivot base you can't get a direct shot at the set screws and it is a real trick to get the standard hex wrench into them. This ball end wrench will easily go into the set screws at an angle so you can get them tight. Great for other Mark V adjustments also.
$11.50
MKC


6 spline Gilmer drive Mark V That's right! Now you can have a precision machined double bearing quill on your superior 6 spline Gilmer drive Mark V. No need to change to the Poly-v system to get a two bearing quill. I machine the the back end of the quill and spindle to accept a new top quality sealed ball bearing. This eliminates movement in the rear of the spindle and cuts the TIR (runout) at the tip of the spindle to .001" or less. This eliminates the need for the plastic noise suppressor on the drive sleeve and it must be removed. The front bearing also replaced with a new sealed bearing to give many years of excellent service. Turn around time is 2 days or less after I receive your quill. Your satisfaction is gauranteed. At times I will have extra quills modified and ready to ship. Check with me.
$135.00

MKC


Now available: A precision machined double bearing quill upgrade for your Mark V Shopsmith with the 14 spline spindle. Fits all Mark V machines from mid 1961 through the current model. I machine the rear end of your quill and spindle to accept a new precision sealed bearing. This cuts the runout at the tip of the spindle to .001" or less. Unlike the factory 2 bearing quill design, the larger rear bearing in these upgrades will last much longer. Plus, you have the original one piece spindle instead of two pieces spindle pinned together.
Your satisfaction is guaranteed.
I can upgrade your single bearing 14 spline quill for $99.50. At times I will have extra quills on hand aready modified and ready to ship for $145.00 plus shipping. Check with me for availability.
$99.50

MKC

Power Tool Woodworking for Everyone by R. J. DeCristoforo. 1980s edition in very nice condition. Clean, tight binding and no marks. This book is probably the best accessory you can have for a Shopsmith. It has a chapter on each function of the machine as well as how to make many useful jigs and other helps.
NA

$19.50

MKC

Mark V 500 table carriage pinoin gears. Very good condition.
Current Shopsmith, Inc. price = 60.00 ea.
$29.50 ea.
MKC

Mark V 500 table carriage square pinoin shaft. Very good condition with end clip.
Currently unavailable from SS,Inc.
$28.50 ea.
MKC

Mark V 500 headstock or carriage lock wedges. Very good condition.
Left and right in stock
$9.95 ea.
MKC

Mark V 500 table headstock or carriage locking rod and handle. Very good condition.

$29.50 ea.
MKC

Mark V table assembly. Later model gray in very nice condition. Complete assembly less insert

Mark V table assembly. Green 50s model in very nice condition. Complete assembly less insert
$45.00
504276

Mark V tailstock complete assembly with eccentric mount and position collars. Very nice condition. Fits all models of Mark V, Mark 2 and Mark VII. Current catalog price is 87.24. Photo is example. Some have cosmetic issues, paint or stains but all fully functional.
45.00
MKC-xxx

1 1/4" shaft collars

These new set screw type collars are used to position SPT tools on the Mark V or the 10ER with my SPT mount adapter. They can also be used for repeat setups on the Mark V table saw and tool rest.
NA
5013799

Shopsmith Mark V 500 saw table insert. Very good condition. No longer available from Shopsmith, Inc.
$28.50
505622

Shopsmith Mark V 500 molding head table insert. Very good condition. No longer available from Shopsmith, Inc.
NA
505509

Shopsmith Mark V 500 shaper/drum sander table insert. Very good condition and includes guide pins. Current catalog price is $43.67.
NA
505621

Shopsmith Mark V 500 dado blade table insert. Very good condition. No longer available from Shopsmith, Inc.
$28.50
Over 40 years experience repairing Mark V and 10ER Shopsmith machines at the most reasonalble prices and fast turn around. Call or email for more info. I have many other Shopsmith parts and accessories. Contact me if you don't see what you need listed.
Custom machine work available.
Price does not include shipping charges
Order by Email skip@mkctools.com  Or Call 817-319-2297
Satisfaction Guaranteed.
Texas residents add 8.25% sales tax.                                  Home